Category: Adventure Riding

  • How Lithium Jumpstarters Work

    These things are a little miracle. A jumpstarter you hold in one hand that I used to start the 6.7 liter diesel in my truck. How can this be? The truck has two lead acid batteries the size of toaster ovens. I left the damned lights on at a race track. Went to start it and click, click… …nothing. I took the little compressor/battery bank/flashlight/jumper from my motorcycle and connected it. Once it gave me a green light I hit the switch. Boom, it turned over faster than it does on a fully charged monster dual battery setup. I did NOT expect that to work. How is that possible?

    The simple answer–the massive C rating and low internal resistance of NMC Lithium batteries. C rating means how fast you can charge it, so maybe we should call it a D rating since we care about discharging more than charging, but the number is the same, and that’s not how it’s described technically. So the C rating of a typical NMC battery used in a jumpstarter pack is 15-30C and in some cases 100C for short periods. NMC batteries are generally used since they store a lot of power in a small size and handle high burst rate discharges. So if pack is rated at 5000mah (milliamp-hours, so 5Ah) a 30C discharge rate means it can supply 150Amps, if it can do 100C in a burst that’s 500amps. Not for long of course. Even at 30C discharge a 5Ah battery cranking a motorcycle at 150 amps will only last about 2 minutes. In reality a start lasting 10 seconds at 150 amps (150 A × 10 s = 1,500 amp-seconds ÷ 3,600 = about 0.42 Ah (417 mAh)) chews up about 1/10th of the capacity–you get ten tries…maybe. But usually one is enough.

    Here’s how they work–it’s more complicated than you think.

    The box you plug into the compressor of main unit or the bulge in the middle of the cable contains a relay or MOSFET switch that only connects the pack when everything checks out and you turn the switch to start. It provides: –Reverse-polarity protection, so the clamps don’t spark or blow the guts out of your jumper box if you get them backwards.
    –Short-circuit and overcurrent protection.
    –Back-feed protection, so the vehicle’s alternator can’t charge the pack.
    –Battery detection: it won’t switch on until it senses a battery at the clamps. A “boost” or override button bypasses this when the vehicle’s battery is almost completely dead. Once that little box is happy it turns the light green–but that’s about all that happens. The battery is in parallel with your dead or semi-dead battery, but you don’t want it to charge the battery, you want to start the vehicle. So when you turn the switch to start, the box senses the current draw (actually, the voltage drop) and triggers the jumper either closing a relay or firing some hefty MOSFETs. Bam–you have 150 or more amps going though some fairly wimpy wires and clamps. If that current flowed for more than a few seconds stuff would melt, but it doesn’t, so all good–apparently. I’m sure this isn’t violating the laws of physics, but it’s pushing at the edge of the box.

    I put a clamp-on hall effect ammeter that can measure and lock inrush current on my little jumper box. On my F350 diesel truck I measured 468 amps with a device the manufacturer claimed was good for 150, so I’d say Your mileage will vary. Started my F350 just fine. I don’t think I should do it often, but it got me going. Honestly, it it fried after that one shot I would have thought it was worthwhile, but it didn’t. It’s fine, I’ve been using it two years since then. It survived about ten tests with the ammeter since I didn’t believe the numbers for the first 9 times, It’s started my Husky 701 a dozen times, filled dozens of tires, and it started my diesel tractor a half dozen or more times (I need to replace that battery).

    Some manufacturers claim “1000A / 2000A peak” , that’s got to be mostly marketing but still…. ..I’m not gonna say they’re liars. A motorcycle starter draws only about 80–150 A, so even a small pack is plenty. The bike only draws what it needs, so a bigger pack won’t hurt it.

    There are Supercapacitor jump starters. They’re a different design. I’ve never used one but they sound very cool. I’ve always wanted to add a super capacitor to a bike battery so if I left the lights on and killed it, I could use the tiny residual charge to pump a capacitor for a minute or two, then release that energy into the starter. 1000 amps for a second or two. That would get my cold-blooded Husky going. Probably snap it right to attention. I finally replaced the crappy AGM battery it had with Lithium, so I suspect it won’t need help anymore. It likes the 13.3 V of the Lithium–downright perky.

  • Sometimes I’m Just Wrong–A tire change I struggled with

    I’ve been telling people for years that changing tires is all about technique, not equipment, and you can change tires easily with just two small aluminum tire irons, and good tire lube. A bead holder is handy but not critical. I’m not wrong for smaller bikes, like dual sport and small-ish adventure bikes, or for vintage bikes with narrower rims than are common these days. But yesterday I changed the rear tire on my Ducati Desert-X, and it was a struggle. The stock rear tire is a Pirelli Scorpion Rally STR 150/70/18. My technique for “breaking” the bead is to slather on tire lube diluted with water and work around the rim with a tire iron, pushing the bead down a bit and letting the tire lube penetrate. After two or three revolutions around the tire the bead can be levered down into the dropcenter easily. But the Ducati has cross spoke, tubeless rims, and there’s no edge on the rim to lever against. So I needed to use my old tire mounting stand which has a simple bead breaker built in. I had to struggle with the bead for about 15 minutes to get it to push into the drop center. The other side went quicker, but was still a struggle. Getting the wheel out of the old tire is usually very easy if you have good tire lube–I generally just pull the wheel out by hand. But the sidewalls were so stiff that I had to use tire irons to get the rim out. About 30 minutes of struggling.

    Mounting the new tire–a Dunlop Trailmax Mission–was quite a battle, the tire has even stiffer sidewalls than the stock Pirelli and the edges of the bead have a soft lip extension that might just be extraneous flash from the molding process, but might be intentional. It grabbed the rim and made it more difficult to lever the tire on. I was tempted to trim it off, but after I looked at it carefully it seemed too regular to be just mold flash. So I left it and just lubed it a bit more. I had to use long steel tire irons to make any progress. I lubed the beads with undiluted tire lube which made the tire and wheel quite slippery. It took me 20 minutes to get one side into the drop center, and then another 30 minutes to finish mounting the tire. The bead stop was a lifesaver, even though it won’t hook onto the spokes because the cross-spoke means the spokes are at a shallower angle, it still keeps the bead from slipping back off the rim, and kept the edge pointed towards the drop center. All in, it was more than an hour of struggling at something that usually takes 15 minutes and I had to use irons that I don’t usually carry. It’s a tubeless tire, I wouldn’t expect to have to dismount it on a ride to fix a flat, but I’m going to have to revisit my toolkit to prepare for the unlikely eventuality that I might have to do something grim by the side of the road. I doubt I could make progress with my dinky aluminum irons that I find so useful for narrower wheels and tires.

    So yes, to anyone I might have mislead or offended with my blithe comment that it’s all just technique–sorry about that. I’ve changed hundreds of motorcycle tires over my riding life, both as a pro mechanic and as a committed amateur with a LOT of bikes and friends that need help with their bikes. I’ve never struggled this much (that I remember). One shop I worked at had a tire machine–I used it several times but it damaged a nice Akront rim so I never used it again. But if I did big wheels and wide tires very often, I might be tempted to try a tire machine or at least built a better stand to do the work.

  • Motorcycle Lubrication

    Motorcycle Lubrication

    Yeah, I know, “what oil should I use” is what bored or clueless folk post on any FaceBook motorcycle forum to see how many pointless comments they can get. Everyone has an opinion on what oil should be used, which is generally what they use, backed by nothing more authoritative than “I’ve been using this for XX years” . Here’s the thing–doing the same thing for a long time is more an indication that the poster has never considered or studied alternatives. It’s more a borderline admission of stubborn stupidity rather than a qualification.

    I love to learn new things, I don’t consider long experience to be a qualification. As I’ve said many times, I’ve been working on bikes longer than most of you have been alive, and I do stupid shit every day. But I do look for expert information, so I’m pleased to offer this email I recently got from “Toxic Terry” who I’ve received great information from previously about chain lube. This is sort of a continuation of that discussion and I hope to take this a bit further this spring, with a deep dive into general lubrication issues, as goofy as that sounds when I type it. Anyway, here’s the latest from Toxic Terry:

    I am the fellow rider who sent you information concerning the potential use of DigiLube Ultra Film 1 for motorcycle chain maintenance. As a retired organic chemist, my interest in lubricants has grown exponentially over the past years as the evolution of synthetic lubricants has become a reality. In the case of DigiLube, the base oil is conventional, but the additive package is synthetic in that the specific lubricant to provide ‘dry lubrication properties’ is a compound that effectively bonds lubricant molecules to the oxide coating present on all common metal surfaces exposed to the environment which contains oxygen. Following application, the base oil [solvent not lubricant] evaporates leaving behind a chemically bonded molecular lubricant that will not wash off with solvents or water and is stable under extreme pressures and moderately high temperatures. Considering the exposure of motorcycle chains to particulates, mud, water, salt, sand and other contaminants, the fundamental property of a bonded dry lubricant is expected to maximize lubrication without retaining solids which can act as abrasives during operation. This is the fundamental property that makes DigiLube an optimum product for motorcycle chain maintenance. Other non-bonded lubricants like silicones and heavy oils/greases all suffer the problem of retaining solids and that is their characteristic weakness if chain longevity is desired.

    Let’s consider automotive lubricants next. Motor oils are grouped into five classes which range from naturally occurring oils [Dyno juice = Class I] to Class V lubricants that are synthesized by reacting small organic molecules to form high molecular weight compounds. To be honest, as a professional organic chemist, the advent of commercially available Class V motor oils should eliminate consideration of using any other lubricant in one’s motorcycle. For that reason, I will not go into all the pros and cons of the Class I to IV lubricants as they are ‘antiquated’ relics compared to the superior properties exhibited by the one of the two kinds of Class V synthetics.

    Class V oils are of two basic types: polyethers and polyesters. Polyethers are not typically used in conventional internal combustion engines as they are ‘sensitive’ to water and in some cases, even soluble in water. Polyesters are the cream of the crop from a chemist’s perspective when it comes to physical properties that are important to provide superior lubrication under extreme conditions of heat and shear. It is for this reason that I recommend using Class V polyester oils in motorcycle engines where the internal components are operating at high speeds, high temperatures with a moderately low volume of lubricant present in the recirculating system.

    As mentioned, diol-based Class V synthetic oils can be synthesized in two formats depending on the initiator molecule. The most common is a diol [a molecule that has an alcohol group attached to each end of a hydrocarbon chain] that reacts with various dicarboxylic fatty acids to form long chain, linear polyesters. These are definitely better than any of the lower class lubricants in terms of their physical properties. However, there is a better molecular structure, one that produces spherical [actually star-shaped is more accurate] molecules which begins with a pentaerythritol initiator. These polyesters, being spherical in structure, provide the ultimate lubricant properties because of their resistance to breakdown under shear. Linear molecules tend to break which produces two chains of shorter length which leads to loss of viscosity and increased volatility. Spherical molecules can suffer a chain break on one of the arms but such degradation has a much reduced influence on viscosity loss because the fundamental molecular weight is reduced by a much lower fraction. While both types of polyesters have similar lubrication properties, those with spherical molecular structure offer significantly longer useful lifetimes from a chemical perspective. Because the manufacturers of synthetic motor oils consider their formulations to be proprietary, it is difficult to understand exactly what type of polyester you are purchasing. However, price per unit volume is often a clue. Lower priced Class V polyester oils are cheaper than the ‘high- end’ varieties that are composed of spherical molecules because of differences in the synthesis procedures employed. My personal understanding to date is the premium motorcycle oils [and automotive oils] from Amsoil are pentaerythritol-based lubricants which yield the spherical molecules I have described.

    So, why are spherical polyester lubricants so effective compared to other motor oils? Pure hydrocarbons are designated non-polar while polyesters are polar. Chemistry teaches that “like dissolves like” which is incredibly important in an internal combustion engine. Combustion byproducts are partially oxidized hydrocarbons which range from carbonaceous solids to a vast variety of other polar substances. Pure hydrocarbon lubricants do not readily dissolve such polar by-products; hence the additives package of the oil must contain considerably higher concentrations of other chemicals to handle the lack of solubility issues. Such additives are not as resistant to degradation as the base oil and have a limited capacity which explains why cheaper oils have much shorter lifetime expectancies under operating conditions. While all motor oils, including Class V polyesters, have a substantial presence of additives to aid in preventing corrosion, adding lubricity, providing cold flow characteristics and viscosity modulation, the amount in the spherical molecular based polyesters is considerably less than all other such motor oils including the linear molecular based polyesters.

    Polyesters are chemically very strong molecules compared to pure hydrocarbons and because polyesters are polar, they adhere strongly to metallic surfaces [compared to pure hydrocarbons] which is the primary reason they are such good lubricants. One notices this property when rebuilding an engine. It is somewhat difficult to remove the oil from parts as typical hydrocarbon solvents [paint thinner] do not readily dissolve it. In my experience, it takes acetone or methylene chloride to effectively remove it from a metal surface. Because polar polyesters dissolve most of the combustion by-products, the oil becomes dark and the internal metallic surfaces remain free of grunge that one encounters when using a pure hydrocarbon oil. The property of spherical molecular polyesters to reduce loss of viscosity caused by chain breakage provides significantly longer operational time between oil changes. Lower concentrations of additives to the base oil also leads to longer lifetimes as the base oil already possesses the necessary properties that the additives provide. Less additives means more base oil per unit volume, and it is the base oil that is the working fluid providing lubricity.

    Bottom line: polyester lubricants have no competition when it comes to the chemical properties that are required for lubricating typical internal combustion engines. Those brands composed of spherical molecules are the best available option if ultimate performance as a lubricant is important. Amsoil, and perhaps some others, have such chemistry which is why I use them exclusively in all my motors.

    OK, cool. So that’s what Toxic Terry says, and it sounds good to me, but what do I know? So I enlisted my friend Mr. Perplexity to do a little fact checking.

    This is Deep Seek R1 (via Perplexity.AI), or rather here’s a link to my query and Deep Seek’s response. The link will open a local version of Perplexity for you. In the unlikely event you worry about opening your kimono to a Chinese AI the perplexity model is housed on Perplexity’s servers in the USA. Perplexity AI is owned by its founders, Aravind Srinivas, Denis Yarats, Johnny Ho, and Andy Konwinski, with a shit ton of outside money from Jeff Bezos and NVidia. I’m in the process of building my own Deep Seek server, just for the hell of it. https://www.perplexity.ai/search/please-analyze-the-following-a-_Zt57GG.SUKGUEnraaXjZg

  • Chain lubricants

    This is the first, of (I hope) many posts from other experts, which was part of the original plan for Expert Amateur. I intended to solicit content from other experts  on various topics. This came unsolicited on the Adventure Riders forum in the 390 ADV owners thread from a member with the unlikely avatar name “Toxic Terry”. I have a heavily modified KTM 390 ADV that I’ve occasionally posted about on the site. I’m publishing this unedited, which is how I intend to handle any other contributions from outside experts. I think the information here clearly meets the requirement of expertise, having a retired Analytical Scientist from Dow Chemical provide thoroughly tested information on chain lubricants is remarkable, and I’m pleased to present this.

    Sir: I am a 77 year old retired Analytical Scientist from The Dow Chemical Company. I am not in your league for riding history, skills, mechanical expertise or most other ‘motorcycle’ stuff. However, I have been riding since 2002: 02 CRF-450, 04 KTM 300, 06 Husky TE-610, 09 Versys 650 [highly modified to become an adventure bike by Dan Djokovic [Indy Unlimited on this site] … and now, a 24 KTM 390 Adventure with tubed spoked wheels and as such have gone through many iterations of chain maintenance. Over the course of the past couple weeks, I have been reading my way through the 800+ pages of the 390 thread and have taken many notes on ‘stuff’ you have attempted to educate the general ridership herein. I appreciate the time and effort you have expended to tell some of your stories and, more importantly, to educate folks on the ‘technical’ background behind many aspects of motorcycles.

    Recently, there were posts regarding ‘chain maintenance’ and as usual, there were many different “opinions” regarding how to maintain a given chain, regardless of its particular build. I read what you had to say and in most respects, are in agreement. But, I do want to provide you with some long-term experimental data I have accumulated over the years trying to figure out what is the best means to maximize chain longevity. Being a laboratory scientist, I have employed the Scientific Method to investigate all sorts of ‘situations’ that involve chemicals and how they interact with physical systems such as conveyors and chains. As such, motorcycle chains are right up my alley as an experimentalist, even when the experiments are conducted in a garage rather than a laboratory.

    Rather than go through the many iterations of chain cleaning and maintenance routines I have explored over the years, I will simply cut to the chase and give you the information I believe to be ‘best practices’. I am not putting this stuff out to the public on this thread because I know how ‘touchy’ folks can get when it comes to engine oil and cleaning chains. LoL … maybe, if you find my information reasonable, perhaps you can ‘advise’ the rest of the inmates … your word will go a lot farther than from a noob like me.

    First, and perhaps foremost, there are no chain lubrication materials in spray cans or otherwise that lengthen a chain’s lifespan. All of these products, some of which actually advertise that their stuff ‘won’t fling off’, result in the deposition of high molecular weight organic hydrocarbons on the surface of the chain. These materials become the perfect abrasive when mixed with inorganic particulates [dirt]. Such abrasives slowly wear on the pin seals and eventually lead to the pins beginning to wear which is the reason the chain grows in length. I frown on the word ‘stretch’ in this case because chains to not stretch. Another way of looking at this phenomenon is to examine a chain that his been operated with a Scott Oiler device. Applying a continuous stream of hydrocarbon oils that are not highly volatile [evaporate easily under normal operating conditions] keeps the chain wet and therefore a better matrix upon which dirt particles can adhere. My riding buddy, Dan Djokovic, had one of these on his BMW F800GS … we installed new chains at the same time [mine on my Husky TE-610 with no oiler], then we ran the bikes until the chains began to lengthen [first data point], then until the chain needed to be replaced. The Scott Oiler chain had to be adjusted after only ~2500 miles and thereafter about every 3 to 4 K miles. Interestingly, my Husky chain, which was treated as described below, didn’t need adjustment for over 8000 miles. The Scott Oiler chain needed to be changed after approximately 10K miles while my Husky chain got almost 15K miles before biting the dust. Dan removed the oiler after this experiment and his chains achieved the same type of longevity as mine using the same treatment procedures. 

    Bottom line: motorcycle chains are best cleaned and lubricated with a material that is composed of a volatile hydrocarbon which serves as the solvent for specialized ‘dry lubricants’. The molecular weight of the hydrocarbon solvent is sufficiently large so as to not be a ‘super good solvent’ like paint thinner, but low enough to evaporate under ambient, or above, conditions. The ‘dry lubricants’ are chemicals that form a strong chemical bond with metal oxides present on the surface of chains exposed to the environment. These dry lubricants essentially form a monomolecular layer of ‘lubricity’ enhancing chemicals that can withstand extreme pressures, will not wash off with either aqueous or non-aqueous solvents, do not attract and retain particulate matter and do not harm any of the polymers used in O- or X-ring pin seals. The downside of such ‘dry lubricants’ is that the monomolecular layer of lubricity will wear off under normal use and therefore needs to be refurbished regularly. In other words, after each day’s ride, reapplication via soaking the chain and wiping dry with a towel, is required and is best achieved while the chain is still warm if possible. This process takes me approximately 2 minutes to accomplish.

    Here’s the magic elixir for chain cleaning, lubrication and general maintenance:

    https://www.digilube.shop/products/

    I have been using this stuff for about 15 years or so … it is absolutely amazing shit to say the least. The only real problem relative to its application to motorcycle chains is the fact that a 5 gallon pail is the smallest commercially available unit. Dan and I have purchased 15 gallons over our years of riding together [unfortunately he passed away a couple years ago] … we repackaged the stuff into gallons and sold our bulk supply to other riders to recoup some of the expense. A gallon will last the average rider at least a year, maybe two, depending how often he rides and how many other things he finds to ‘clean & lubricate’. Just for the record, I use this stuff to lube almost every moving part of my motorcycles: pegs, levers, etc. Works really well on garage door bearings too … much better than that messy lithium grease often recommended. 

    There are a couple more points that need be mentioned regarding chain maintenance that are in my opinion important factors in longevity. The first one involves installing a brand new chain. As received, chains are coated with a low molecular weight paraffin hydrocarbon [wax] as a storage preservative. Failure to remove this wax can dramatically shorten the life span of a given chain. I have seen many folks just wipe the chain with a rag, or a solvent-soaked rag, then install it. The preservative wax is bad news in that it melts under operating conditions, can accumulate in the gap surrounding the pin seals, then collect dirt particles and begin the abrasion process. To avoid such a result, removing the wax is imperative, however, submerging the chain in any hydrocarbon-based solvent is not recommended as solvents like paint thinner can penetrate the pin seal and dilute the captured grease in the link slot leading to premature failure. I have found that placing a new chain in a plastic dish pan, adding about 2 ozs of Digilube 1 to the pan, sloshing the chain around in the solvent, then scrubbing the outside surfaces of each link with a soft bristled tooth brush. Remove the chain from the pan, thoroughly wipe with a clean towel, then lay the chain on a bench and using the toothbrush, dipped in residual Digilube that was in the dish pan, brush each inner surface of the links and finally, wipe chain with the clean towel. Flip the chain over on the bench, repeat the process again from the other side. Upon a final wipe with a clean towel, looking at the inner surfaces of the chain should reveal no visible wax remaining. I sometimes need a Q-tip to augment the toothbrush, but I am OCD as hell and a fanatic about operating principles. This process takes me about 30 minutes to accomplish.

    The second important point involves routine daily ‘relubrication’ after each ride. This process is simple. Lift the real wheel so you can spin the chain, drip Digilube 1 from a plastic dispensing bottle on the chain as it passes over the rear sprocket. The chain needs to receive a thorough soaking with Digilube to the point that it is dripping off the chain. If any macro particulate deposits are observed, use a brush to remove them [usually not necessary from my experience, but if one just ran through a mud hole prior to ending the ride, then definitely a possibility], and finally wiping the chain with a rag to remove excess lubricant and any residual particulates. 

    Not sure if many folks know about Digilube 1, but from my perspective as someone who is fascinated by minutiae, it is ‘magic’ in bottle. Sorry if this catches you off guard, but hopefully something you find interesting to add to your repertoire of motorcycling mayhem. 

    Regards:

    Terry Nestrick 

    [Toxic Terry is my handle from ages ago when folks knew me from my reputation as an ultra-trace analyst specializing in the measurement of dioxins and other noxious chemicals commonly found in the environment and commercial products]